A&D SV-10A Instruction Manual Page 37
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
35
5 After measurement, the buzzer sounds and the displayed
value blinks, then holds.
Note
When the values do not stabilize because of hand
movement, set the condition function that levels the
large variation in digits (refer to page 54) and the
function that do not display the large variation in digits
(refer to page 55) if necessary.
With the portable type, you can use the auto hold
function and timer mode function (refer to page 57).
6 To stop the measurement, press the STOP key.
To go on to the next measurement, set the sample and press
the START key.
When the viscosity value is below the measuring range, Sl TOP is displayed.
When the viscosity value exceeds the measuring range, SH TOP is displayed.
If the sensor plates are not in vibrating motion for about 20 seconds, for example, when
the sample coagulates, the measurement will stop automatically.
∗1 When using the graphing program RsVisco, of the AX-SV-53-EX software set, click the
START button of the RsVisco program to start a measurement.
∗2 While the measurement is being performed using the graphing program RsVisco of the
AX-SV-53-EX software set or data are being output continuously (function setting "prt 2"
or SIR command), the data hold mode using the HOLD key is not available.
Below is an example of the SV-10H at shipment.
(Standby mode)
(Measurement mode)
(Data hold
after measurement)
- SV-A series 1
- SV-H series 1
- CONTENTS 3
- 1. INTRODUCTION 5
- 1-2 Features 7
- 2. UNPACKING THE VISCOMETER 9
- Accessories for SV-1A 10
- Water jacket (1 pc) 11
- Polycarbonate, 5 11
- Polycarbonate 11
- SV-10A / SV-100A 12
- X-Y-Z stage 13
- Install from forward 13
- Display unit 14
- Serial number 16
- Sensor plate 16
- 3. CHANGING TYPE 18
- Next item of 19
- (Standby mode) 19
- From the previous page 19
- 4. DISPLAY AND KEYS 22
- 4-2 Keys (For all models) 23
- 4-3-1 SV-1A/SV-1H 24
- 4-3-2 SV-10A/SV-10H 25
- 4-3-3 SV-100A/SV-100H 25
- 5. PRECAUTIONS 26
- Temperature 28
- 5-5-1 At Measurement 29
- 5-5-2 At Calibration 30
- 6. MEASUREMENT 31
- Approx. 25cm 32
- Below is an exam 34
- (Measurement mode) 37
- (Data hold 37
- SV-1A/SV-1H/ SV-10A/SV-10H 38
- SV-100A/SV-100H 38
- 7. USING THE WATER JACKET 39
- 7-2. Installation 40
- 7-3. How to Use 42
- 7-5. Maintenance 43
- 7-6. Specifications 43
- 8-2-1 One-point Calibration 47
- 8-2-2 Two-point Calibration 48
- of the purified 50
- Setting example 60
- Press and hold 61
- Date/Time (Cladj) 63
- To current 65
- (Go to page 61) 65
- 9-4-2 D.P. Format 68
- 9-4-3 CSV Format 69
- ,,,+025.67,C,+00001.23,mPa s 73
- ,,,+025.67,C,+00001.23, Pa s 73
- 10-1 Introduction 76
- Tab, and click 78
- RS-232C Serial Interface 81
- Pin Connections 81
- Display unit rear side 81
- 13. COMMAND LIST 82
- (FOR ALL MODELS) 82
- 14. TROUBLESHOOTING 83
- (For all models) 85
- 15. ERROR DISPLAY 87
- 16. SPECIFICATIONS 88
- 17. OPTIONAL ACCESSORIES 90
- AX-SV-33 Sample Cup 91
- Plastic storage container 94
- WinCT-Viscosity 95
- RS232C straight 95
- Serial-USB converter 95
- AX-SV-55 Cup Set (2 mL) 97
- Sample cup 97
- Square glass 99
- (Lid attached) 99
- Sensor unit (Handle*) 100
Related products and manuals for Measuring, testing & control A&D SV-10A
(2 pages)
AEG L75370TL Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Waschmaschinen AEG L75370TL.
Wir stellen 2 PDF-Handbücher AEG L75370TL zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comments to this Manuals